Chromed Steel Frame with fixed armrests, footrests.
- Overall width 64cm
- Seat Width 46cm
- Real wheel dia. 58cm
- Front wheel dia. 20cm
- Seat Height 49cm
- Overall height 87cm
- Measurment 93 X 21 X 87cm
GENERAL CARE - Wipe chrome parts with a clean, soft cloth at least once a week. All metal parts can be cleaned with auto wax or similar products. If exposed to moisture, dry immediately.
DO NOT use an abrasive cleanser that will scratch the finish.
WHEELS - Large rear wheels should be inspected at least once a month to ensure proper tightness. Test
for proper tightness and alignment by leaning chair to one side and spin wheel.
TIRES - Solid rubber tires need minimal maintenance, but should be cleaned occasionally with a damp cloth. Replace if tires become severely worn or cracking appears.
FRONT CASTERS - Casters should be checked periodically and lubricated occasionally.
SEAT UPHOLSTERY - Wash the upholstery at least once a month with soapy water. Confirm that the upholstery is dry before using. Sanitize between uses.
HAND GRIPS - Use only a clean towel dampened with cool water when cleaning hand grips. Confirm that the grips are dry before using. NEVER use ammonia-based cleaning solutions or soap on hand grips. This may cause the handgrip s to loosen or slide off the frame.
If you do not understand the manual, contact us for a complete explanation of the Instructions, cautions and warnings. Otherwise, injury or damage may result.
TO OPEN CHAIR - Open wheelchair by tilting to one side and pushing down on seat rail until fully opened.
TO CLOSE/FOLD CHAIR - First fo ld foot plates to vertical position. Grab seat with both hands at front and back edge, then lift. Or, tilt chair to one side and lift upon seat rail.
REMOVABLE ARMS - Remove arms by depressing spring button and lifting arms out of front and rear sockets.
ADJUSTING LENGTH OF FOOTREST/LEGREST - When adjusting length of footrests or legrests, user should be sitting In wheelchair with feet on the foot plates. Loosen bolt on the clamp around support assembly. Raise or lower foot plate to desired position that will provide maximum support or thighs. Front rigging should not be so low that it causes uncomfortable pressure to thighs at front of seat upholstery. Footrest should not be lower than 21⁄2" from the ground to ensure proper clearance.
ADJUSTING ELEVATING LEGREST - Lift foot plate on legrest assembly to desired position. Release legrest assembly and it will automatically lock into place. To lower, push out on legrest lever and lower foot plate to desired position .
REMOVAL OF SWING-AWAY FOOTRESTS/LEGRESTS - Release lock by pushing on the front rigging lever. Swing-away footrest/legrest out and sideways. Lift to remove.
WHEEL LOCKS - Engage both wheel locks before getting in or out of chair, leaning forward in chair, or while in an elevator or wheelchair lift. Test for correct locking action before actual use.
STABILITY - Wheelchair is designed to be safe and stable as long as the center of gravity is maintained while going about normal activities.
Care must be taken while performing activities that shift your center of gravity while in the chair.
NEVER reach so far that you have to shift In the seat or bend over out of the chair. When you have to reach for objects that require you to lean. be certain front caster are point ing in a forward position that extends the wheel base and aid in stabilizing the chair.
RAMPS - Be sure of your own capabilities, limitations and strength before attempting to go up a wheelchair ramp. Correct techniques on ramp negotiation should be shown to you by a qualified professional. Assistance is recommended when going up or down inclines greater than 10 degrees . If you must stop on an incline, avoid sudden, abrupt movement when you resume movement. Sudden movement could cause instability. Attempting to use the wheel lock brakes could result in accidental locking, tipping to one side, or cause a sudden stop. Avoid changing direction when going down an incline, as this could result in instability and tipping over.
DO NOT ATTEMPT TO ADJUST OR OPERATE WHEELCHAIR WITHOUT READING ALL INSTRUCTIONS CAREFULLY.
This wheelchair has not been approved as a seat that can be used within vehicles of any kind. ALWAYS transfer wheelchair user to a vehicle manufacturer's approved seat and use safety restraints available.
DO NOT operate this wheelchair on roadways, streets, or any surfaces with vehicular traffic. DO NOT attempt to operate on inclines 10° or greater without proper assistance.
Be sure to completely engage wheel locks when getting in and out of wheelchair or when in elevator or wheelchair lift.
Wheelchair should be on a smooth, stable and level area with wheel locks engaged before transferring user in or out of wheelchair.
DO NOT adjust footrests any lower than 2 1⁄2" from floor. When getting in or out of wheelchair, DO NOT stand on or apply weight to footrests.
Before reaching or leaning forward, rotate casters to front of the wheelchair engage wheel locks to help prevent wheelchair from tipping over.
DO NOT lean over or apply weight on the top of wheelchair back. This can cause wheelchair to tip over. When trying to extend arms over back, only reach as far as your arm can extend without having to alter your seating position.
DO NOT stand on wheelchair.
DO NOT use wheel locks to slow your descent down an incline. Abruptly changing directions while going down an incline could cause Instability or possible tipping over.